Hersteller von Netzteilen

Triac-Dimm-LED-Treiber der Serie PE294R mit 3–12 W

PE294 is one of the constant current dimming LED driver developed by my company with high power factor ,high efficiency, high precision, the use of the efficient stable low loss switch control chip and the high performance components makes it with low noise, energy saving, environmental protection, long life and other characteristics.

  • Marke:

    QINX
  • Art.-Nr.:  

    PE294R
  • Eingangsspannung:

    200-265Vac
  • Arbeitsmodus:

    Constant Current
  • Dimmmodus:  

    Triac dimmable
  • Größe:  

    104×39×26mm
  • Zertifizierung:  

    SAA CE ROHS
Produktbeschreibung

Merkmale:

  • LED phase-cut dimming driver, dimming range 2-100%
  • Suitable for RPC MOSFET dimmer and FPC TRAIC dimmer
  • Aktiver PFC
  • Protections: short circuit/over voltage/over current
  • Silica gel heat conduction technology,natural cold wind
  • Ultra small volume
  • Suitable for LED home lighting and commercial lighting
  • Safe no load protection device
  • Economic and convenient installation
  • conform to the world lighting equipment safety standards
  • Protection class II
  • 3 Jahre Garantie

General description:

PE280 is one of the constant current dimming LED driver developed by my company with high power factor ,high efficiency, high precision, the use of the efficient stable low loss switch control chip and the high performance components makes it with low noise, energy saving, environmental protection, long life and other characteristics.

█ Specification

Modell     PE294R2435    PE294R4225     PE294R4230    PE294R24250     PE294R1570PR294R1570
   AUSGABEAusgangsspannung     12-24Vdc    25-42Vdc     25-42Vdc   12-24Vdc     6-15Vdc2.5-6Vdc
Max Output Voltage     24Vdc    42Vdc     42Vdc    24Vdc     15Vdc6Vdc
Non-load Output Voltage     27Vdc    45Vdc     45Vdc    27Vdc     19Vdc8Vdc
Output Current     350mA    250mA     300mA    500mA     700mA700mA
Ausgangsleistung     4.2W~8.4W    6.2W~10.5W     1.75W~4.2W    6W~12W     4.2W~10.5W1.75W-4.2W
Strobe Level      Lower flicker(8%)
Dimming Range      2~100%,
Current Accuracy      ±5%
Ripple & Noise      =500mv p-p
   EINGANGDimming Interface      Triac Leading edge/Tralling edge
Eingangsspannungsbereich      200-250Vac
Frequency      50/60Hz
Input Current      <0.072A    <0.08A      <0.08A      <0.08A<0.08A
Power FactorPF>0.9(at  full  load)PF>0.9(at  full  load)PF>0.88(at  full  load)PF>0.88(at  full  load)PF>0.88(at  full  load)
THD      230Vac@THD     <20% (at full  load)
      77%     79%      77%    77%      77%
Inrush Current(typ.)    Cold start 1.44A   Cold start 1.54A   Cold start1.54ACold start1.32A   Cold start1.54A
Anti Surge      L-N: 1.5kV
Leckstrom      <0.25mA/230Vac
UMFELDWorking Temperature      ta: 55 °C  tc: 85  °C
Arbeitsfeuchtigkeit      20 ~ 95%RH, non-condensing
Storage Temp., Humidity      -40 ~ 80  °C   , 10~95%RH
      ±0.03%/°C(0-50)°C
Vibration      10~500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes.
SCHUTZOver-heat Protection      Intelligently adjusting or turning off the output current if the PCB temperature ≥110°C, , auto recovers.
Over Load Protection      Shut down the output when rated power≥102%, auto recovers.
Short Circuit Protection      Shut down automatically if short circuit occurs, auto recovers.
Non-load Protection      Shut down the output if no load, auto recovers when load back to normal.
SAFETY &
EMV
Withstand VoltageI/P-O/P: 3750Vac
Isolation ResistanceI/P-O/P: 100MΩ/500VDC/25°C/70%RH
Safety StandardsIEC/EN61347- 1, IEC/EN61347-2- 13
EMC EmissionEN55015, EN61000-3-2 Class C, IEC61000-3-3
EMC ImmunityEN61000-4-2,3,4,5,6,8,11,  EN61547
Strobe Test StandardIEEE 1789
   OTHERSDimension104×39×26mm(L×W×H)
Verpackung105*46*26.5mm
Weight(G.W.)68g

Maße :

 

Wiring Diagram:

█ Compatibility:

    Dimming system ModelWring 1 sampleWring 2 samplesWring 3 samplesDimmer ModelWring 1 sampleWring 2 samplesWring 3 samplesDimmer ModelWring 1 sampleWring 2 samplesWring 3 samples
Leviton  LNPWR-05BNFNFNFPanasonic WMY549NFNFNFBG DM400AP UKNFNFNF
Siemens 5WG1 528- 1DB01NFNFNF  Siemens 5UH82223-NC01NFNFNFCLIPSAL 32E540LMNFNFNF
JOBO dimming systemNFNFNFSimon 45E201NFNFNFCLIPSAL 32E540UDMNFNFNF
DALITEK  DM802NFNFNFOPPLE  P068102NFNFNFCLIPSAL 32E54TMNFNFNF
Lutron  QSGR-3PNFNFNFCABLOFIL VRCM2NFNFNFHPM CAT 400LNFNFNF
ABB  6197/12- 12- 101-500NFNFNFCDN X6-TG02NFNFNFKAOYI KDT-450ANFNFNF
Crestron  DIN- 1DIM4NFNFNFELKO 315GLEDNFNFNFLEGRAND 400TNFNFNF
Schneide  L5504D2ArNFNFNFELKO 316GLEDNFNFNFLEGRAND 400LNFNFNF
DAJIN  DC-TG0405CPNFNFNFPOL CAT634LMNFNFNFDIGINET DGLCDM400NFNFNF
Lite-Puter  EDX-F0411NFNFNFDETA Gr 100 UKNFNFNF
    Rmarks     Abbreviation: no flicker – NF, not compatible – NC, slight flicker – SL, flicker – F, strict flicker – SF

Note: due to the different power of dimmer and dimming system, the compatibility will be different. Before purchase, it needs to confirm
with the business to ensure the best matching effect of the product.

█ Wiring:

The output wire: 20AWG red and black PVC cable ,length 200-230mm,wire stripping requirement:5-7mm

The input wire : 20AW Brown Blue VDE double insulated wire, length 150-160mm,wire stripping requirement:5-7mm

The use of guidance:

**1:please pay attention to the distinction betweeninput and output,connect correctly,then power on

**2: please connect first the load of the DC output, open the powersupply after checking; in the constant current mode, if power on at open circuit,please turn off the power supply and can’t connectthe LED until the electric energy stored by the output release , or it may damage the LED;

**3:this type of power supply is only limited to the use of the LED lamps and lanterns, the input voltage range is AC200-250V, the

Specified output voltage, current range, the use environment temperature is -20-45 degrees,and the surface can not cover the

heat insulation cotton and other items that obstruct the heat dissipation of the product, which conforms to the product under the

conditions of the environment, this product enjoys three yearsof free warranty.

The abnormal conditions and the corresponding treatment methods:

l, the LED lamp doesn’t bright after the dimming driver is connected at the first time ,please turn off the AC input and check as follow:

a) Whether or not DC output bad contact;

b)Whether DC output polarity is reversed, or the LED board is welded anti;

c)Whether AC input is bad contact;test after eliminating these failures.

2, the device has good connection, LED lights, but the LEDflicker, please turn off the AC input, then check the DC output;

a) overload, under load.

b) Whether or not the parameters and actual parameters match.

3,please timely communicate with us if you any questions inthe using,we will try our best to solve the problems with you.

Statement:

The pictures and specifications is for reference only, in kind prevail, specifications are subject to change with further notice.

Eine Nachricht hinterlassen

    Wenn Sie mehr über unsere Netzteile/Netzteile/LED-Treiber/Ladegeräte erfahren möchten, senden Sie uns bitte eine E-Mail. Wir werden Ihnen in Kürze antworten.

    Ähnliches Produkt
    100 W TRIAC 0–10 V 2-in-1-Dimm-Netzteil, kein Flimmern, LED-Treiber

    100 W TRIAC 0–10 V 2-in-1-Dimm-Netzteil, kein Flimmern, LED-Treiber

    It adopts CPU control and designs a variety of control modes. The dimming is slow on and off. The raw materials used are first-line brands and imported chip ultra deep dimming design,It matches a variety of intelligent dimming systems and dimmers on the market. Aluminum alloy shell, rapid heat dissipation, makes the thermal balance of components more stable.

    12–18 W Triac-Dimm-LED-Treiber der Serie PE296R

    12–18 W Triac-Dimm-LED-Treiber der Serie PE296R

    PE296 is one of the constant current dimming LED driver developed by my company with high power factor ,high efficiency, high precision, the use of the efficient stable low loss switch control chip and the high performance components makes it with low noise, energy saving, environmental protection, long life and other characteristics.

    Triac-Dimm-LED-Treiber der Serie PE294R mit 3–12 W

    Triac-Dimm-LED-Treiber der Serie PE294R mit 3–12 W

    PE294 is one of the constant current dimming LED driver developed by my company with high power factor ,high efficiency, high precision, the use of the efficient stable low loss switch control chip and the high performance components makes it with low noise, energy saving, environmental protection, long life and other characteristics.

    PE281 3–12 W kleiner Triac-Dimm-LED-Treiber

    PE281 3–12 W kleiner Triac-Dimm-LED-Treiber

    PE280 is one of the constant current dimming LED driver developed by my company with high power factor ,high efficiency, high precision, the use of the efficient stable low loss switch control chip and the high performance components makes it with low noise, energy saving, environmental protection, long life and other characteristics.

    PE280 small size with built-in ERP compliant triac dimming led driver

    PE280 small size with built-in ERP compliant triac dimming led driver

    PE280 is one of the constant current dimming LED driver developed by my company with high power factor ,high efficiency, high precision, the use of the efficient stable low loss switch control chip and the high performance components makes it with low noise, energy saving, environmental protection, long life and other characteristics.

    QINX

    Verbinde dich mit uns
    Wenn Sie an unseren Produkten interessiert sind und weitere Einzelheiten erfahren möchten, hinterlassen Sie bitte hier eine Nachricht. Wir werden Ihnen so schnell wie möglich antworten.
    So erreichen Sie uns.

      Copyright © Qinx Technology Co., Ltd.. Alle Rechte vorbehalten.
      Willkommen bei QINX

        Um mehr über unsere Netzteile/LED-Treiber/Netzteile/Ladegeräte zu erfahren, senden Sie uns bitte eine E-Mail. Wir werden Ihnen bald antworten.

        Heim

        Produkte

        Um

        Kontakt