█ Features:

1. Constant voltage triac dimming driver dimming range 0-100%
2. Support leading edge dimmer and leading edge dimming system
3. Support 0-10V / 1-10V / 10V PWM / 100k potentiometer dimming
4. No stroboscopic dimming, super compatible dimming power supply
5. Protection type: short circuit / overcurrent / overvoltage
6. Aluminum alloy shell, fast heat dissipation
7. Unique design, slow on and slow off function
8. Suitable for constant voltage LED strip light and other applications
9. Meet SELV safety extra low voltage standard
10.   5 years warranty

█ Application:

1. Constant voltage lamp strip, hard lamp strip
2. Support leading edge system dimming
3. Villa, high-end hotel and other applications
4. Ultra thin light box

█ Specification:

█Dimensions :

█ Product Label:

█ Wiring:

1 . Input wire: wire gauge 3- core wire , 1m2, length 190MM , stripping 6-7mm (tin coating)

2 .Output wire: wire gauge , 2- core wire , 1m2, length 190MM , stripping 6-7mm (tin coating)

3 .Signal wire: wire gauge 2- core wire 0 .75 square , 190MM length , 6-7mm stripping (tin coating) 4 . External signal wire: 1 . 5m2 copper core shielded wire, less than 200m long

█ Wiring Diagram:

Note: 0-10V signal wire s hall not be short circuited or grounded when using silicon controlled rectifier for dimming , otherwise dimming will be affected .

 220V       N             0/1-10V(-)signal      0/1-10V(+)signal

█ Compatibility:

Note: 1.due to the different power of dimmer and dimming system, the compatibility will be different. Before purchase, it needs to confirm with the business to ensure the best matching effect of the product. 2 . It is recommended to use a leading edge dimmer power more than 500W.

█ 0/1-10V LOAD:

1. Accordingto the actual measurement, the number of 200M controllable power supplies of 1.5 square signal lines used for 1-10V signal interface of Aidimming dimmer is 100
2. Compatiblewith the dimming system of most big brands on the market
3. Itis forbidden to connect the signal interface with high voltage, otherwise the power supply will be damaged

█ Working Curve:

█ The use of guidance:

Note:

1. Whenusingthis power supply , please pay attention to distinguish between the input end and theoutput end. Please connect the wires correctly. There are positive and negative poles for the output .The power can only be turned on after checking;

2. Pleaseconnect the load at the DC output terminal , confirm it is correct , and then turn on the power supply;
3. Theinputvoltage range of the product is AC200-250V , the output is within the specified voltage range , and the output power is within the specified use range ,The ambient temperature for use is – 20 to+45 ℃ , and the surface cannot be covered with heat insulation cotton and other articles that block the heat dissipation of the product ,This product is guaranteed free of charge for five years in an environment that meets the product ‘s use conditions .

4. Theinputend of dimming power supply shall not be connected with inductive variable frequency power supply for dimming , otherwise noise will be generated.

█ The abnormal conditions and the corresponding treatment methods:

1. Thepowersupply does not light up after the electrical connection of the device is completed for the first time. Please cut off the AC input terminal and check :
2. a) WhethertheDC output terminal has poor contact;
3. b) Whether thepositiveand negative electrodes of DC output end are connected reverse ly and whether the LED board is welded reverse ly;
4. c) Whether the ACinput terminalhas poor contact; Test again after the above faults are
5. After thedeviceis electrically connected , the LED light is on, but the LED light flashes. Please cut off the AC input terminal and check the DC output terminal :

1. a) Whetherthereis overload or light load ;
2. b) Thedesignparameters of the power supply are inconsistent with the actual parameters (whether they are within the design output voltage range of the power supply) .

3) . In case of other questions or problems during the use of the product, please timely communicate with our company and feed back bad information ,Our company will actively assist your company in solving problems .

Not covered by the warranty:

1. thesignalcontrol interface s hall not be connected to a voltage higher than 15V to damage the power supply
2. inputand output connections are reversed , resulting in power damage
3. thepowersupply is damaged due to water ingress