Fabrikanten van voedingen

3W built-in bare board power supply

The QLA03A product is with easy installation and can be used on the mainboard with terminals directly.

  • Model:

    QLA03A
  • Ingangsspanning:

    85-264V AC of 110-370V DC.
  • Werkmodus:

    AC-DC
  • Maat:

    3.6*2.1*1.8cm
  • Stroom:

    3W
Productbeschrijving

Product features:

1.The product is with easy installation and can be used on the mainboard with terminals directly.

2.Iternational Universal input voltage: 85-264V AC or 110-370V DC.

3.The product has high efficiency with long use, high power density ,100% full load aging and high output voltage accuracy to 1%.

4.High isolation between input and output which adapt to Wide Environment Temperature – 25 – 70 degrees (CE Safety Standard with 40 degrees)

5.Types of protection: overcurrent protection, short circuit protection and temperature protection. Natural cooling has no noise and with long life.

6.Output built-in 105 degree with long life electrolytic capacitor.

7.The product meets to CE safety standard design, no load less than 0.1W, and with 75% Efficiency.

8.Ultra-low standby, six-level energy efficiency, ultra-thin design, three years of quality assurance.

 

Item

 

 

Voorwaarde

Common models of this series we have (we can customize any products with different output voltage and current or other requirements according to customer’s requirements )
QLA03A-0505QLA03A-0512QLA03A-0524

1 、Invoer Features

Working Voltage Range(VAC)85-264
Frequency Range(Hz)47-63
AC-ingang (VAC)85-264
DC-ingang (VDC)110-264
Input Current(mA)0.07/ 115VAC   0.03/230VAC
Schommelingsstroom (A)Cold Boot:10A/230VAC
Efficiency(TYP .)68%70%70%
Stand-by power consumption(mW)≤ 100mW

2 、Uitvoer Functies

Uitgangsspanning (VDC)Main Circuit 5VSubcircuit 5VMain Circuit5VSubcircuit 12VMain Circuit5VSubcircuit 24V
Nauwkeurigheid uitgangsspanningDual-Channel ± 1%
Geschatte stroom (ADC)V01:0.4AV02:0.2AV01:0.24AV02:0. 15AV01:0. 12AV02:0. 1A
Rated power (W)3W3W3W
Ripple&Noise

(mvp-p)

Nominale invoer

voltage , 20MHz

bandbreedte

≤50mV≤ 100mV
Lineair aanpassingspercentageVolle lading± 1%
Belastingsregeling10- 100% Belasting±3%
Startup and rise timeVolle lading2000ms, 30ms/ 115VAC    1000ms, 30ms/230VAC
Behoud

tijd (ms)

Volle lading16ms/ 115VAC  50ms/230VAC
Overbelasten

bescherming

Nominale ingangsspanning115%- 150% of the rated output power(Overload Protection )
Protection mode: hiccup mode, auto-response after removal of abnormal loading condition
Kortsluitingsbeveiliging 

Nominale ingangsspanning

Automatisch herstel na langdurige kortsluiting
Overstroombeveiliging≥ 1.5 times Io
Start delay

tijd (ms)

 

 

Vin: 230VAC

Uitschakelen

protection time

(ms)

 

20 ms

3 、Algemeen Features

Working      temperature(℃)/-25-70
Working humidity

(RH)

/20-90%, non-condensing
Temperature drift coefficient/±0.02%/℃
Opslagtemperatuur en vochtigheid-40~+85℃ 10-95%RH
Switching frequency (KHz)5-65  (Frequency Conversion Control Chip)
Isolation voltage

(VAC)

Input-to-output, test duurde 60s,≤

5mA

 

3KV≤5mA  60S

Insulation     resistance(MΩ)Input-to-output,

500VDC

100
Leakage    current(mA)500VDCInput-to-output    ≤ 1mA/RMS
MTBF@25℃>250000H
Veiligheidsniveau/Adaptation :CLASS B
Trillingen

weerstand

/10—500Hz 2G 10 minutes/cycle . 60 minutes each for X, Y and Z.
Elektromagnetische compabiliteit/Adaptation :EN55022(CISPR22) Class B  EN61000-3-2,-3
 

 

 

Opmerkingen

1. Except for special instructions , the parameters of this specification are measured at 230VAC input, rated load and 25℃.

2. Measurement of ripple and noise: Using a  12” twisted pair, and the terminal has two capacitors , 0. 1uF and 10uF in parallel . Measured at 20MHz bandwidth .

3. Accuracy: Including errors, linear adjustment rate and load adjustment rate .

4. The power supply should be regarded as part of the components in the system, and electro-magnetic compatibility related confirmation should be carried out with the terminal equipment .

5. Reduced output is required under low input voltage . Please refer to the reduction graph.

EMC Circuit Recommendation

Sollicitatie schematic diagram

Product selection and Notes:

1.Please refer to the specifications in detail for selection and use, otherwise the reliability of power supply will not be guaranteed.

2. Alle parameters van deze specificatie worden gemeten volgens de interne normen van ons bedrijf.

3.It is suggested that the load power of the power supply should not exceed 80% of the rated power of the power supply.

4.With multi-output power supply, each output circuit must be loaded and used at the same time according to the corresponding ratio.

5.Our company can provide customized products.

6.We reserve the right to change specifications without prior notice.

Laat een bericht achter

    Als u meer wilt weten over onze voedingen/voedingsadapters/LED-drivers/opladers, stuur ons dan een e-mail, wij zullen u spoedig antwoorden.

    Gerelateerd product
    QLL17W-serie ingebouwde kale board open frame voeding 17Watt PSU

    QLL17W-serie ingebouwde kale board open frame voeding 17Watt PSU

    The QLK17W product is with easy installation. Input/output with 90 degree 2.54 row needles, which can be used for reserved hole welding wire hole.

    QLI05W series built-in bare board open frame power supply 5Watts

    QLI05W series built-in bare board open frame power supply 5Watts

    The QLI05W product is with easy installation. Input/output with 90 degree 2.54 row needles, which can be used for reserved hole welding wire hole.

    QLF12 12W AC-DC-stroommodules van hoge kwaliteit

    QLF12 12W AC-DC-stroommodules van hoge kwaliteit

    The productis easy to install and can be mounted on the main board of socket (AC inputVH3.96-3A2/DC output VH3.96-2A). The plug can be directly inserted and used, and the welding hole can be reserved.

    3W built-in bare board power supply

    3W built-in bare board power supply

    The QLA03A product is with easy installation and can be used on the mainboard with terminals directly.

    built-in bare board open frame power supply 10Watts

    built-in bare board open frame power supply 10Watts

    The QLA10A product is with easy installation and can be used on the mainboard with plug directly.

    QINX

    Verbind je met ons
    Als u geïnteresseerd bent in onze producten en meer details wilt weten, laat dan hier een bericht achter, wij zullen u zo snel mogelijk antwoorden.
    Manier om contact met ons op te nemen.

      Copyright © Qinx Technology Co., Ltd.. Alle rechten voorbehouden.
      Welkom bij QINX

        Als u meer wilt weten over onze voedingsadapters/LED-drivers/voedingen/opladers, stuur ons dan een e-mail, wij zullen u spoedig antwoorden.

        Thuis

        Producten

        Over

        Contact