Power Supplies Manufacturers

PE281 3-12W small size triac dimming led driver

PE280 is one of the constant current dimming LED driver developed by my company with high power factor ,high efficiency, high precision, the use of the efficient stable low loss switch control chip and the high performance components makes it with low noise, energy saving, environmental protection, long life and other characteristics.

  • Brand:

    QINX
  • Item No.:  

    PE281B
  • Input Voltage:

    200-265Vac
  • Working Mode:

    Constant Current
  • Dimming Mode:  

    Triac dimmable
  • Size:  

    55.5×39×23.5/60mm(L×W×H/D)
  • Certification:  

    SAA CE ROHS
Products description

Features:

  • LED phase-cut dimming driver, dimming range 2-100%
  • Suitable for RPC MOSFET dimmer and FPC TRAIC dimmer
  • Active PFC
  • Protections: short circuit/over voltage/over current
  • Silica gel heat conduction technology,natural cold wind
  • Ultra small volume
  • Suitable for LED home lighting and commercial lighting
  • Safe no load protection device
  • Economic and convenient installation
  • conform to the world lighting equipment safety standards
  • Protection class II
  • 3 years warranty

General description:

PE280 is one of the constant current dimming LED driver developed by my company with high power factor ,high efficiency, high precision, the use of the efficient stable low loss switch control chip and the high performance components makes it with low noise, energy saving, environmental protection, long life and other characteristics.

█ Specification

Model     PE281B2435    PE281B4225     PE281B4230    PE281B2450     PE281B1570
   OUTPUTOutput Voltage     12-24Vdc    25-42Vdc     25-42Vdc   12-24Vdc     6-15Vdc
Max Output Voltage     24Vdc    42Vdc     42Vdc    24Vdc     15Vdc
Non-load Output Voltage     27Vdc    45Vdc     45Vdc    27Vdc     19Vdc
Output Current     350mA    250mA     300mA    500mA     700mA
Output Power     4.2W~8.4W    6.2W~10.5W     1.75W~4.2W    6W~12W     4.2W~10.5W
Strobe Level      Lower flicker(8%)
Dimming Range      2~100%,
Current Accuracy      ±5%
Ripple & Noise      =500mv p-p
   INPUTDimming Interface      Triac Leading edge/Tralling edge
Input Voltage Range      200-250Vac
Frequency      50/60Hz
Input Current      <0.072A    <0.08A      <0.08A      <0.08A<0.08A
Power FactorPF>0.9(at  full  load)PF>0.9(at  full  load)PF>0.88(at  full  load)PF>0.88(at  full  load)PF>0.88(at  full  load)
THD      230Vac@THD     <20% (at full  load)
      77%     79%      77%    77%      77%
Inrush Current(typ.)    Cold start 1.44A   Cold start 1.54A   Cold start1.54ACold start1.32A   Cold start1.54A
Anti Surge      L-N: 1.5kV
Leakage Current      <0.25mA/230Vac
ENVIRONMENTWorking Temperature      ta: 55 °C  tc: 85  °C
Working Humidity      20 ~ 95%RH, non-condensing
Storage Temp., Humidity      -40 ~ 80  °C   , 10~95%RH
      ±0.03%/°C(0-50)°C
Vibration      10~500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes.
PROTECTIONOver-heat Protection      Intelligently adjusting or turning off the output current if the PCB temperature ≥110°C, , auto recovers.
Over Load Protection      Shut down the output when rated power≥102%, auto recovers.
Short Circuit Protection      Shut down automatically if short circuit occurs, auto recovers.
Non-load Protection      Shut down the output if no load, auto recovers when load back to normal.
SAFETY &
EMC
Withstand VoltageI/P-O/P: 3750Vac
Isolation ResistanceI/P-O/P: 100MΩ/500VDC/25°C/70%RH
Safety StandardsIEC/EN61347- 1, IEC/EN61347-2- 13
EMC EmissionEN55015, EN61000-3-2 Class C, IEC61000-3-3
EMC ImmunityEN61000-4-2,3,4,5,6,8,11,  EN61547
Strobe Test StandardIEEE 1789
   OTHERSDimension55.5×39×23.5/60mm(L×W×H/D)
PackingPE  bag
Weight(G.W.)75g±10g

Dimensions :

pe281_D

Product Label:

pe281_D_label

Wiring Diagram:

pe281_D_wring

█ Compatibility:

    Dimming system ModelWring 1 sampleWring 2 samplesWring 3 samplesDimmer ModelWring 1 sampleWring 2 samplesWring 3 samplesDimmer ModelWring 1 sampleWring 2 samplesWring 3 samples
Leviton  LNPWR-05BNFNFNFPanasonic WMY549NFNFNFBG DM400AP UKNFNFNF
Siemens 5WG1 528- 1DB01NFNFNF  Siemens 5UH82223-NC01NFNFNFCLIPSAL 32E540LMNFNFNF
JOBO dimming systemNFNFNFSimon 45E201NFNFNFCLIPSAL 32E540UDMNFNFNF
DALITEK  DM802NFNFNFOPPLE  P068102NFNFNFCLIPSAL 32E54TMNFNFNF
Lutron  QSGR-3PNFNFNFCABLOFIL VRCM2NFNFNFHPM CAT 400LNFNFNF
ABB  6197/12- 12- 101-500NFNFNFCDN X6-TG02NFNFNFKAOYI KDT-450ANFNFNF
Crestron  DIN- 1DIM4NFNFNFELKO 315GLEDNFNFNFLEGRAND 400TNFNFNF
Schneide  L5504D2ArNFNFNFELKO 316GLEDNFNFNFLEGRAND 400LNFNFNF
DAJIN  DC-TG0405CPNFNFNFPOL CAT634LMNFNFNFDIGINET DGLCDM400NFNFNF
Lite-Puter  EDX-F0411NFNFNFDETA Gr 100 UKNFNFNF
    Rmarks     Abbreviation: no flicker – NF, not compatible – NC, slight flicker – SL, flicker – F, strict flicker – SF

Note: due to the different power of dimmer and dimming system, the compatibility will be different. Before purchase, it needs to confirm
with the business to ensure the best matching effect of the product.

█ Wiring:

The output wire: 20AWG red and black PVC cable ,length 200-230mm,wire stripping requirement:5-7mm

The input wire : 20AW Brown Blue VDE double insulated wire, length 150-160mm,wire stripping requirement:5-7mm

The use of guidance:

**1:please pay attention to the distinction betweeninput and output,connect correctly,then power on

**2: please connect first the load of the DC output, open the powersupply after checking; in the constant current mode, if power on at open circuit,please turn off the power supply and can’t connectthe LED until the electric energy stored by the output release , or it may damage the LED;

**3:this type of power supply is only limited to the use of the LED lamps and lanterns, the input voltage range is AC200-250V, the

Specified output voltage, current range, the use environment temperature is -20-45 degrees,and the surface can not cover the

heat insulation cotton and other items that obstruct the heat dissipation of the product, which conforms to the product under the

conditions of the environment, this product enjoys three yearsof free warranty.

The abnormal conditions and the corresponding treatment methods:

l, the LED lamp doesn’t bright after the dimming driver is connected at the first time ,please turn off the AC input and check as follow:

a) Whether or not DC output bad contact;

b)Whether DC output polarity is reversed, or the LED board is welded anti;

c)Whether AC input is bad contact;test after eliminating these failures.

2, the device has good connection, LED lights, but the LEDflicker, please turn off the AC input, then check the DC output;

a) overload, under load.

b) Whether or not the parameters and actual parameters match.

3,please timely communicate with us if you any questions inthe using,we will try our best to solve the problems with you.

Statement:

The pictures and specifications is for reference only, in kind prevail, specifications are subject to change with further notice.

Leave a message

    To know more our power supplies/Power adapters/LED drivers/Chargers, please send email to us, we will reply to you soon.

    Related Product
    PE280 small size with built-in ERP compliant triac dimming led driver

    PE280 small size with built-in ERP compliant triac dimming led driver

    PE280 is one of the constant current dimming LED driver developed by my company with high power factor ,high efficiency, high precision, the use of the efficient stable low loss switch control chip and the high performance components makes it with low noise, energy saving, environmental protection, long life and other characteristics.

    PE294R series 3-12W triac dimming led driver

    PE294R series 3-12W triac dimming led driver

    PE294 is one of the constant current dimming LED driver developed by my company with high power factor ,high efficiency, high precision, the use of the efficient stable low loss switch control chip and the high performance components makes it with low noise, energy saving, environmental protection, long life and other characteristics.

    PE296R series 12-18W triac dimming led driver

    PE296R series 12-18W triac dimming led driver

    PE296 is one of the constant current dimming LED driver developed by my company with high power factor ,high efficiency, high precision, the use of the efficient stable low loss switch control chip and the high performance components makes it with low noise, energy saving, environmental protection, long life and other characteristics.

    PE281 3-12W small size triac dimming led driver

    PE281 3-12W small size triac dimming led driver

    PE280 is one of the constant current dimming LED driver developed by my company with high power factor ,high efficiency, high precision, the use of the efficient stable low loss switch control chip and the high performance components makes it with low noise, energy saving, environmental protection, long life and other characteristics.

    100W TRIAC 0-10V 2 in 1 Dimming Power Supply No Flicker Led Driver

    100W TRIAC 0-10V 2 in 1 Dimming Power Supply No Flicker Led Driver

    It adopts CPU control and designs a variety of control modes. The dimming is slow on and off. The raw materials used are first-line brands and imported chip ultra deep dimming design,It matches a variety of intelligent dimming systems and dimmers on the market. Aluminum alloy shell, rapid heat dissipation, makes the thermal balance of components more stable.

    QINX

    Connect With Us
    If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.
    Way to contact us.

      Copyright © Qinx Technology Co., Ltd..All Rights Reserved.
      Welcome To QINX

        To know more our Power adapters/LED drivers/power supplies/Chargers, pls send email to us, we will reply you soon.

        Home

        Products

        About

        Contact